Frequency
Type of code
- Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
- Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.
Buttons
Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.
PROCESS:
- In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
- Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.
If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.
Copy
No copy
ELVOX® ETR 5 Remote
HOW TO SYNCHRONISE ELVOX ROLLING CODE REMOTE CONTROLS
ELVOX remote control synchronisation can only be performed directly on the receiver itself.
Synchronising the remote control directly on the receiver
Sliding and hinged doors
1. Hold the button on the receiver I2(P2).
2. While still holding the button on the receiver, press the button on the remote control to be synchronised.
3. Wait for the LED to flash, confirming the synchronisation.
4. Release both buttons.
ECRU receiver
1. Hold the button on the P1 receiver for two seconds. The DL1 LED will flash green.
2. Release the P1 button on the receiver.
3. Press button 1 on the remote control to be programmed.
4. The blue DL5 LED will flash.
5. On pressing the P1 button again for two seconds, the DL2 LED will flash green to synchronise channel 2.
6. Press button 2 on the remote control to be programmed.
7. The blue DL5 LED will flash.
8. To synchronise buttons 3 and 4, repeat steps 5 to 7. The LEDs DL3 and DL4 will light. Press buttons 3 and 4 in each case.
9. To leave synchronisation mode, press buttons P1 and P2 when the green LED flashes while waiting for a signal.
TORMATIC® MS41 Remote
CAME® ATO Remote
SYNCHRONISING CAME ROLLING CODE REMOTE CONTROLS
CAME ATO remote controls can be synchronised either directly or remotely by taking the following steps.
Synchronisation procedure using the receiver
1. Press the button of the desired channel on the receiver for 2 seconds.
2. The LED on the receiver will flash.
3. Press the button of the same channel on the remote control to be synchronised. Press the button for the same channel on each remote control in turn if you wish to synchronise more than one device.
4. The LED on the receiver will change to steady each time a button is pressed.
5. Repeat the process for the other channel.
Remote synchronising procedure
1. Press the button of the desired channel on the remote control for 15 seconds.
2. The LED on the receiver will flash.
3. Press the button of the same channel on the remote control to be synchronised. Press the button for the same channel on each remote control in turn if you wish to synchronise more than one device.
4. The LED on the receiver will change to steady each time a button is pressed.
EMFA® MAP868 Remote
SYNCHRONISING JCM ROLLING CODE REMOTE CONTROLS
The JCM rolling code remote control synchronisation procedure is identical for all models except the 868 MHz.
There are 3 synchronisation procedures for these devices.
PIN-MODE remote synchronising procedure
The following procedure must be applied if the receiver bears the words PIN-MODE:
1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the remote control to be synchronised.
The receiver will emit a long beep, indicating that the device has been successfully synchronised.
Remote synchronisation procedure using the original remote control
1. Stand near the receiver and use a pointed object to press the pushbutton at the rear of the synchronised remote control.
The receiver will emit a beep, indicating that it has switched to synchronisation mode.
2. Within 10 seconds of the beep, press the button on the device to be synchronised.
The receiver will emit another short beep to indicate that the remote control has been synchronised.
If the receiver fails to synchronise the device (does not emit the short beep) it may mean that the memory is full and the remote control cannot be synchronised without the installer\'s permission.
3. After 10 seconds the receiver will exit synchronisation mode and emit 2 short beeps.
Direct synchronisation procedure on the receiver
1. Open the receiver and locate a switch or pushbutton labelled \"PROG\".
2. Press the button or turn on the switch.
The receiver will emit a long beep and the LED will light up. From this point, follow the previous procedure from step 2 above.
TORMATIC® MCHS Remote
SYNCHRONISING NOVOFERM ROLLING CODE REMOTE CONTROLS
The Novoferm remote control can only be synchronised directly on the receiver.
Direct synchronisation procedure on the receiver
1. Open the receiver and press the button located inside until the LED begins to flash.
2. Then press the button on the remote control and hold for approximately 3 seconds until the LED begins to flash quickly.
Take the following steps if the facility has a ceiling-mounted motor.
The selected remotes can not be copied with a single JMA remote