FIND YOUR REMOTE

Find your remote and compatable JMA Remote to copy

Legend: Click on the symbols for further information

Frequency

Type of code

  1. Fixed. The code emitted by the remote control, is always the same. There is no encryption and once the remote control is duplicated, the copy works directly in the receiver.
  2. Rolling. The code emitted by the remote control, changes with each pulse. A copy of the remote control should be made, that way generating the same brand and model but with a different serial number, that will be necessary for registry in the receiver. There are specific instructions for each receiver of either how to register the copy, remotely or directly manipulating the receiver.

Buttons

Auto-Programmable The remote control can be registered in the receiver without the need of the original remote control, as long as radio communication is activated and the memory is not full.

PROCESS:

  1. In front of the receiver keep the JMA remote control pressed during 10 seconds until the red LED goes off (after 4 seconds) and it turns to green (at 10 seconds).
  2. Once the LED is green, release the button and wait for the LED to definitely go off. During the process, the green LED will flash once or several times depending on the code type until finally going off.

If the process does not work, test the standard method using the original remote control or gaining access directly from the receiver.

Copy

No copy

NOVOFERM® FHS

  • F 40,685
  • C FIX CODE
  • B 1,4
  • AP NO
  • Q-UICK
NOVOFERM® FHS

See compatible JMA remotes

NOVOFERM® M512

  • F 433,92
  • C FIX CODE
  • B 1,2
  • AP NO
  • BASIC / M-BT / SIMPLY FR1
NOVOFERM® M512

See compatible JMA remotes

NOVOFERM® MCHS

  • F 433,92
  • C ROLLING CODE
  • B 2
  • AP NO
  • M-BT / SIMPLY FR1
NOVOFERM® MCHS

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING NOVOFERM ROLLING CODE REMOTE CONTROLS

The Novoferm remote control can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver

1. Open the receiver and press the button located inside until the LED begins to flash.

2. Then press the button on the remote control and hold for approximately 3 seconds until the LED begins to flash quickly.

Take the following steps if the facility has a ceiling-mounted motor.

NOVOFERM® MNHS

  • F 433,92
  • C ROLLING CODE
  • B 2,4
  • AP NO
  • M-BT / SIMPLY FR1
NOVOFERM® MNHS

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING NOVOFERM ROLLING CODE REMOTE CONTROLS

The Novoferm remote control can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver

1. Open the receiver and press the button located inside until the LED begins to flash.

2. Then press the button on the remote control and hold for approximately 3 seconds until the LED begins to flash quickly.

Take the following steps if the facility has a ceiling-mounted motor.

NOVOFERM® MS41

  • F 40,685
  • C FIX CODE
  • B 1,2,4
  • AP NO
  • Q-UICK
NOVOFERM® MS41

See compatible JMA remotes

NOVOFERM® NOVOTRON

  • F 433,92
  • C ROLLING CODE
  • B 2,4
  • AP NO
  • M-BT / SIMPLY FR1
NOVOFERM® NOVOTRON

See compatible JMA remotes

Synchronising intructions

Print

SYNCHRONISING NOVOFERM ROLLING CODE REMOTE CONTROLS

The Novoferm remote control can only be synchronised directly on the receiver.

Direct synchronisation procedure on the receiver

1. Open the receiver and press the button located inside until the LED begins to flash.

2. Then press the button on the remote control and hold for approximately 3 seconds until the LED begins to flash quickly.

Take the following steps if the facility has a ceiling-mounted motor.

NOVOFERM® S41

  • F 40,685
  • C FIX CODE
  • B 1,2,4
  • AP NO
  • Q-UICK
NOVOFERM® S41

See compatible JMA remotes